Skip to content
Beginner track · lesson 2 of 35 minutes

Install it

In one lineType two lines in Claude Code, pick "Install for you," done in 5 minutes.

Open Claude Code the way you usually do, and work in the box where you chat with the AI. There are three steps.

Step 1: add the plugin store

/plugin marketplace add cursor/plugins

✓ Successfully added marketplace: cursor-plugins

Step 2: install pstack, pick Install for you

/plugin install pstack@cursor-plugins

❯ Install for you

···

✓ Plugin is now active.

Step 3: type /pstack: without pressing Enter; poteto-mode in the list means it's installed

/pstack:

/pstack:poteto-mode

/pstack:how

/pstack:bro

···

DiagramIllustration: roughly what the three steps look like in Claude Code. The real screen shows a few more lines.

Step 1: tell it where to find pstack

Copy this line, paste it into the box, and press Enter:

This adds Cursor’s “plug-in store.” pstack lives there, and Claude Code can install from it too.

You should see

You see Successfully added marketplace: cursor-plugins. The store was added.

Step 2: install pstack

Copy this line and press Enter:

pstack’s details open on screen, with three options below asking who it’s for.

Use the ↑ ↓ arrow keys to pick the first one, Install for you (works in any folder), and press Enter.

You should see

The last line says Plugin is now active. If it says Run /reload-plugins to apply instead, do what it says: type /reload-plugins and press Enter.

Step 3: check that it’s installed

Type /pstack: in the box, and don’t press Enter yet.

You should see

A list of commands that start with pstack: pops up, and /pstack:poteto-mode is one of them. If you see it, you’re done. Press Esc to close the list.

From now on, commands start with pstack:

A plugin install puts every pstack command under pstack:. You type /pstack:poteto-mode; plain /poteto-mode isn’t recognized. That’s Claude Code’s rule for all plugins, so two plugins can’t clash over a name.

No need to memorize it. Commands on this site are written that way by default, so you can copy them as they are. Not using Claude Code? Pick your tool here and every command on the site changes to match:

I use

Commands on this site are shown for this tool, so copying just works

Shown as: /pstack:poteto-mode

Nothing else needs setting up. It works as soon as it’s installed.

If something’s off

When I type /plugin, it says the command doesn't exist.

Your Claude Code is too old. Update it first:

  1. Type /exit and press Enter to quit Claude Code.
  2. In the same window, type claude update, press Enter, and wait for it to finish.
  3. Type claude and press Enter to open it again. Start over from step 1.
Step 2 says it can't find pstack.

Step 1 probably didn’t work. Type the step 1 line again, wait for Successfully added marketplace, then do step 2.

Nothing pops up when I type /pstack:.

First, reopen it: type /exit to quit, type claude, then try /pstack: again.

Still missing? Type /plugin and press Tab to get to the Installed page. Check that pstack is there and turned on.

I use Cursor, not Claude Code.

Type /add-plugin pstack in Cursor’s chat box and it’s installed. Commands in Cursor have no pstack: prefix: pick Cursor under “I use” above, and the next lesson’s commands switch to how Cursor writes them.

If you stop using it

Type this line in the box and press Enter to uninstall pstack:

Then type /reload-plugins and press Enter (or reopen Claude Code), and the /pstack: commands are gone. To install it again later, start over from step two. To pause it for a while instead, use disable in place of uninstall, and enable when you want it back.

An unofficial beginner's guide to pstack, not its official docs. pstack is made by poteto; the official repo is the source of truth for commands and behavior. The original guide source is on GitHub.

Hosted by airali. Adapted from Xiaoxiaodong's MIT-licensed guide.